Your Comfort is our Specialty
(262) 547-2030
24 Hour Emergency Service!

Service/Maintenance

Need service or repairs?

Our professional, NATE certified technicians are available 24 hours a day / 7 days a week to handle any situation you may have with your system.  Call our office after hours and you will speak to a person at our answering service who will contact one of our techs and dispatch them to your home immediately.

Our techs are knowledgeable on servicing all major brands of equipment and take pride in making sure your equipment is operating correctly and efficiently.

BRANDS WE SERVICE:

Carrier - Goodman - Bryant - Payne - Armstrong - Heil - Trane - Lennox - York - Rheem - Mitsubishi - Fujitsu - Reznor - Burnham - Crown - Munchkin - NTI - Navien            

Signup for our Maintenance Package below and receive valuable savings & benefits year round on  service or tune-ups!

Premium Maintenance Package

Maintaining your heating & cooling system is as important as having the oil changed on your car or checking your tire pressure…it’s intended to improve your efficiency, protect your equipment and give you  peace of mind that everything is operating safely.

 

OUR PREMIUM MAINTENANCE PACKAGE INCLUDES THE TUNEUP & THE FOLLOWING BENEFITS:

NO OVERTIME RATES ON DIAGNOSTIC CHARGE OR SERVICE REPAIRS (regular business hour rates)

AN ADDITIONAL 15% DISCOUNT (excludes diagnostic charge) ON SERVICE REPAIRS & ACCESSORIES * some restrictions may apply

SERVICE REPAIR WARRANTIES – 180 DAYS ON LABOR (industry standard is 30 days) AND ONE YEAR ON PARTS

PRIORITY SERVICE – USUALLY SAME OR NEXT DAY

NO PREPAYMENT – PAY WHEN TUNEUP IS COMPLETED

EQUIPMENT IS COVERED FOR ONE FULL YEAR WITH ALL THE ABOVE BENEFITS

*Package does not include boilers or commercial maintenance - call for pricing

 
 
FURNACE TUNE UP & SAFETY INSPECTION
TUNE UPS INCLUDE THE FOLLOWING AT NO ADDITIONAL CHARGE:
  • Check heat exchanger for rust/cracks/holes
  • Check venting for rust/corrosion
  • Check gas valve for leaks/corrosion
  • Check control wiring & connections
  • Check gas lines for rust/corrosion/support
  • Measure incoming gas pressure
  • Check for CO in supply
  • Inspect low & high voltage wiring
  • Check burners for rust/proper operation
  • Check ignition for proper operation
  • Check burner setup
  • Check blower assembly for vibration/dirt buildup
  • Check hot surface ignitor/spark ignition
  • Check blower timing
  • Check pressure switch & tube
  • Measure gas pressure at burners
  • Measure heat exchanger pressures
  • Measure hot surface ignitor OHMS
  • Measure AMP draw inducer motor/blower motor
  • Measure CO in exhaust
  • Measure temperature rise
  • Check drains for proper drainage
  • Inspect t-stat & settings
  • Observe unit starting sequence
 
 
AIR CONDITIONING TUNE UP & SAFETY INSPECTION
TUNE UPS INCLUDE THE FOLLOWING AT NO ADDITIONAL CHARGE:
  • Check t-stat & settings
  • Check drains for proper drainage
  • Check blower wheel for excessive dirt
  • Check TXV for tightness
  • Check lineset for tightness
  • Check 24V wiring to outside wall
  • Check condenser breaker
  • Check 240V wiring to outside wall
  • Check outdoor coil
  • Check wall penetration for proper seal
  • Check 240V connections
  • Check high voltage disconnect
  • Check unit ground & tighten
  • Check contactor visually for burn marks/pitting
  • Check fan motor visually
  • Check fan blade for damage
  • Check capacitor visually
  • Check all wiring connections & tighten
  • Measure capacitance of run/start cap
  • Measure ambient temperature
  • Measure voltage at load side of contactor
  • Measure voltage drop at contactor
  • Measure super heat
  • Measure sub cooling
  • Measure fan AMP draw
  • Measure compressor AMP draw
  • Measure temperature at coil
  • Measure condenser AMP draw
 

Click here for full brochure of benefits and pricing

Service/Maintenance Request
FOR EMERGENCY SERVICE PLEASE CALL 262-547-2030. OUR TECHNICIANS ARE AVAILABLE 24 HOURS DAYS/365 DAYS A YEAR!

Request an Estimate